Installation
Calculating Materials
Stone Flats – Length x width = sq . ft . needed
Stone Corners – Vertically measure each corner = linear sq. ft. needed
Mortar – Non-Grouted Projects equal approximately 3 bags per 100 sq . ft . Grouted Projects equal approximately 4 bags per 100 sq . ft . (Quantities include scratch coat)
Sand – 150 lbs . of sand per bag of mortar (we sell masonry sand by the yard = 4 scoops)
Felt Paper – In most cases 400 sq. ft. per roll
Metal Lathe – NOTE: It is recommended to sponge off walls and back of stone to remove any dust or debris before applying stone. (we sell metal lathe at approx. 32 sq. ft. per sheet)
Water Management
Please note that stone and mortar of any kind are not waterproofing systems. Felt paper must be used on all exterior mortar applications with the exception of untreated block, brick, masonry stucco, concrete or other untreated, unpainted masonry products . Follow all requirements according to building code standards prior to installation. This includes but is not limited to: flashing, weather resistant wrap, and flashing tape around windows and doors.
Mortar Preparation
Standard Type S or N Mortar is used in applying stone. The following are recommended mixing instructions based upon (1) 84lb. bag of masonry:
(1)84lb. Bag of Type S or N Masonry = 150 lbs. of sand
Approximately 3-4 Gallons of water Mix to desired consistency
(Some sand may be more wet or dry depending on
sand provider. Adjust water to compensate.)
Apply a thicker scratch coat (less water), and thinner setting mortar (more water)
Metal Lathe
Install metal lathe to studs using galvanized nails or staples every 6-12 inches on center with a minimum of 1” penetration. Overlap lathe sides a minimum of 2” maximum 3”.
Scratch Coat
Apply a 1/2” scratch coat of mortar covering every cell of lathe . Strike lines in the scratch coat with a notched trowel or coarse brush for added mortar lock bond. Allow time to cure.
Grout/Joint Finish
A grout bag is used to fill the voids between stones . All grout joints must be pressed and tooled with tug pointing tools. For a standard grout application apply between stones, allow grout to become firm, then use a tug point tool to rake the excess grout to the depth desired . Candelbrie Stone recommends a grout joint on all applications . Based on the desired look, you may use anything from a wider joint down to a snug minimal joint for drystack applications. Our Quickfit product can be applied with no grout joints but we highly recommend a snug joint for proper adhesion and desired aesthetic.
Features
The average thickness of stone veneer is 1 ½ inch but depends on the style and texture with 1”- 2” being common. Veneer does NOT carry a load requiring a stone/brick ledge poured with the slab.
Stone Veneer as an industry favorite:
– Any type In Any Color
– Less Expensive Than Natural Stone
– Half The Weight Of Natural Stone
– Maintenance Free
– Durable
Specifications & Technical Data
Technical Data & Testing
Average thickness . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . .1.5″
Average installed weight . . . . . . . . . . . . . . . . . . . . . . . . . . .12-14 lbs . per sq . ft .
Compressive Strength . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . . . . . . XXXX p .s .i .
Average Water Absorption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . .XX%
R Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . XXX
Non combustible, Flame Spread . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0
Shipping/Packaging
All stone products equal approx. 120 sq. ft. per pallet. Hearthstones, Capstones, Keystones, Trim and Sills can be sold individually or by the pallet. A pallet weighs approximately 750 lbs ea.
Specifications for Brick Veneer
7” x 2” x 1”
xx lbs per Brick
7.5 bricks = 1 square foot
4.5 brick = 1 linear foot of corners
954 pieces makes 100 sq. ft.
72 pieces makes 10 lr. ft.
Warranty
25 year Warranty from date of purchase. Must be used on a structure conforming to local building codes and installed in accordance with manufacturer’s instructions. Replacement of stone at no charge if determined to be defective. This warranty is non-transferrable and does not cover labor costs incurred in removal and replacement. Hearthstones are not covered under warranty for use on the ground or as a surface area subject to foot traffic.
This warranty does not cover damage resulting from:
. Settlement of the building or other wall movement
. Contact with chemicals or paint
. Staining or oxidation
. Discoloration due to airborne contaminants